Circuit Breaker Is on but No Power to Outlet: Possible Reasons and SolutionsIn today’s world, power outages are a common occurrence. But what if your circuit breaker is on, but you have no power to the outlet? This can be frustrating, and many homeowners may not know why this happens or how they can fix it. Luckily, there are some easy solutions that should work for most people.

Daven Electric specializes in getting the power back on as fast as possible so that customers don’t have to live without electricity or run their generators endlessly. We’re always available when emergencies occur. We offer emergency services like Electrical Installation in Brooklyn, repair and replacement work. Trust us to get things fixed ASAP!

Why Does Your Outlet Have Power But Isn’t Working? Here’s How to Fix It

Electricity is already part of our daily lives. We turn on the lights, open up our computers and use them – all of these things are possible because electricity is present. But what happens if your electric power isn’t working? If you find yourself wondering why there’s no power going anywhere else in the house even when your breaker is on, these are some possible reasons:

  1. Tripped Circuit Breaker
  2. Wiring Issues
  3. Overloaded Circuit
  4. Damaged Electrical Outlet
  5. Blown Fuse
  6. Lightning Strike
  7. Power Strip or Surge Protector Problems
  8. Missing Cover Plate

What is a circuit breaker purpose?

Circuit breakers are installed in homes to protect an electrical system from overload. A circuit breaker is usually located right next to the main breaker box where all of the power lines come into the house, and it protects that particular circuit or branch of circuits from being overloaded. The purpose is not only for safety but also to prevent fire hazards due to damaged wiring or other issues with a home’s electric system

The circuit breaker is tripped.

If the circuit breaker is on, but there’s no power to an outlet because it has been activated, you’ll need someone with training in electrical work. It’s possible that the breaker for this particular circuit has been tripped and needs to be reset before power can flow. A qualified electrician will be able to restore power without any danger of electrocution.

Wiring problem

Another possible reason why the circuit breaker is on and no power to an outlet can be a wiring issue. It may not have anything to do with your outlets, but it could be that the wires behind them are damaged or disconnected. Ensure you check all of the connections on both ends of each wire before assuming they’re okay. Check the circuit breaker and outlet for loose wires, frayed cables, or damaged wiring. If there is a risk of electric shock from any exposed metal parts on either the cable or inside an outlet box, unplug it to investigate further before proceeding with anything else. You want to make sure there aren’t any loose plugs, switches, fuses, or sockets, especially in older houses where something like this might happen more often than you’d think!

Exceeding the amperage rating

Ensure that you are not plugging too many high-watt devices into one power strip or wall outlet at once (e.g., running several small appliances off a single bar heater). The combined wattage of all plugged-in devices should never exceed what your circuit breaker can handle effectively. Your fuse/circuit breaker may be tripped if this happens due to overload; consult its instructions for resetting it. You might need professional assistance in this case; contact a Brooklyn electrician immediately and take care of the problem as soon as possible so that it doesn’t get worse.

The electrical outlet is damaged.

Sometimes the outlet is just old and damaged due to use. The simplest solution would be replacing that outlet with something newer, but if it’s not an option for you, try using a power strip instead. Plug everything into the power strip rather than plugging them all directly into one socket at once, and this way, you’ll avoid overloading anything.

The main fuse has blown.

This could be due to issues with the fuse, where it’s either too small or has blown. You can check this by looking for burn marks around the house and inspecting all fuses inside your home (especially where they’re mounted near the panel box) as well as breakers. If this is an issue, you may need a whole new circuit breaker panel installed by a qualified electrician.

A lightning strike your home

It could be that your house was struck by lightning and it took out some of your wirings as well! This is one of those instances where you need professional help, but if you’re not sure, try turning off every breaker in the main panel for at least 30 seconds before flipping them back on again. If this doesn’t work, call an electrician right away!

The power strip or surge protector is not plugged in properly

One of the reasons there is no power is because the power strip or surge protector is not being plugged in properly. If the outlet is on, but there is no power, make sure that you have plugged your extension cord into a working outlet and then plug it into the other end of the power strip.

Missing cover plate

The last thing we’ll talk about as far as reasons for no power at an electrical socket? Is if there’s a missing cover plate over one of your receptacles. This would prevent current from flowing and would also spark a fire since there’s no safety mechanism to keep the power from arcing.

Things You Can Do to Fix the Issues

In a world where power outages are common, it can be frustrating when you have no power to your outlet. However, there are some easy solutions that should work for most people. If you’re experiencing this problem and don’t know what is wrong or how to fix it, contact Daven Electric today! We’ll be glad to help figure out the issue so that you can get back on track with life without worrying about working around an inconvenient outage.

  • Check circuit breaker panel – Maybe it’s not at fault after all! To do this, first, turn off the breakers on both phases of the electric service (don’t forget about those 120v plugs in closets), Then switch each lever back on individually from left to right like they were initially positioned until something pops up with a humming sound. This is also called cycling because we are essentially turning things “on” and “off” in order to reset the circuit breaker.
  • Check cables from panel to outlet – Sometimes, it can be as simple as loose or frayed wires that need to be fixed. Be sure not to put all the blame on the outlets just yet!
  • Check all power cords for “grounding” plugs that are attached to an outlet with two slots instead of three (a ground slot). There could be too much electricity going through your home’s circuits, so you’ll need to add more outlets by installing additional sockets elsewhere in your house. Place them as close as possible to where people spend most time-such as living rooms, kitchens, and bedrooms.
  • Inspect wiring at panel box – Occasionally (especially when there are many old cable connections), some of these wires might get damaged by too much pressure over time, and they may need replacing.
  • Replace Outlet Wires – You might have some wires frayed from overuse, so replacing the wires in the outlet is a good idea. You can also replace old wiring using copper wire rather than aluminum wire because its conductivity may not disperse heat evenly over long distances like aluminum does when carrying a current.
  • Replace Cord – If your cord is damaged, it may not be supplying power to the outlet. If you’re unsure about how a new replacement will look with the old wall color and style, hang onto it until after painting or re-wallpapering so that you can match up the colors as close as possible. You can also replace worn insulation on power cords with some new foam or rubber to prevent electric shock and fire hazards.
  • Strip and Replace Outlet – Sometimes, to fix an outlet that is having problems, you may need to strip it out (remove the cover plate) and replace just the socket without re-wiring or replacing wiring in your home. If your outlet isn’t working properly even when plugged into another, swap it out for a fresh one! They’re cheap enough at home improvement stores these days, so it’s not a cost issue.
  • Move power strips to different outlets – If you’re using a power strip for extension cords or devices that can’t be plugged directly into an outlet- try moving them around. Sometimes just changing one plug’s position in relation to another may solve your problem. 
  • Place Outlet Away From Other Appliances – You want to make sure that your cord isn’t crossing with another appliance’s cords since this could cause a short circuit or overload. It also helps to place appliances according to their voltage requirements as listed on them, such as putting anything requiring 220 volts away from items only needing 110 volts which would reduce chances of an overload happening because there are fewer outlets available for use by those appliances needing different voltages.
  • Cords Near High Traffic Areas – Place cords where they won’t get in people’s way of walking past them out of habit, like around kitchen counter edges nor near doorways to avoid tripping on them by accident while moving through those areas.
  • Only One Plug Working – If only one plug on one side of a duplex-style wall outlet works, then try swapping outlets with its opposite at the same height up there so if left plugs work when plugged into right outlets, then vice versa and see which sides now have power!
  • Outlet Reset Button – Don’t forget about those reset buttons next to each outlet, as they can help people who accidentally shut off their breaker by pressing too many keys at once on a keyboard while typing an email or Facebook update!
  • Outlet Cover Plate – Sometimes, a cover plate for an outlet can get loose and need to be tightened. You may also want to make sure your home’s circuit breaker is on before you go about this step.
  • Remove any devices connected via extension cord – Extension cords are only meant to be used temporarily; just until someone gets there, who knows what they’re doing and will fix this issue properly. 
  • Check connections behind furniture – Loose wires sticking out of furniture often lead to no power in one area where the wire is plugged into another outlet but won’t reach because there’s too much other stuff blocking access. Pulling all plugs out from the back of the shelving and furniture and then tightening any loose connections will often fix the problem.
  • Make sure all plugs are securely inserted – Sometimes, people don’t push their plug fully into the wall socket (or unplugged devices can fall out) and stop working. If you’re not sure, unplug it and press the plugin again – if that fixes your problem, then call an electrician to put a tamper-resistant receptacle for safety purposes or install a power strip with an on/off switch so you can cut off power at the source when necessary.

Getting Your Power Back By Calling an Electrician

The best way to get your power back when there is no power in your home, business, or office building is to call an electrician. Daven Electric Corp., a family-owned company with over 80 years of experience, can be reached 24/365 if you need help restoring power quickly.

Professional electricians by Daven Electric are trained in safety procedures. There are many problems that need to be diagnosed before a problem can be fixed, but electricians have the tools and training for identifying these issues quickly. They will also know how to use less destructive methods of diagnosing your problem, which means they’ll get you back on the grid faster than if you were guessing what’s wrong yourself or following YouTube tutorials. Hiring a Brooklyn electrician is cheaper than hiring someone who doesn’t do electrical work as their full-time job, which could lead to costly mistakes.

Contact Daven Electric Corp. today! Give us a call at (212) 390-1106, and we’ll get you back to full power as soon as possible.